• Register
Product Code: 1305-04069

PowerMAX Cat.6 Shielded Toolless Jack

You Can Request Pricing By Building Up An RFP:
- +

PowerMAX Cat.6 Shielded Toolless Jack

The DINTEK PowerMAX™ Category 6 solutions are guaranteed to exceed ClassE channel specifications as set down in International standards.

Our PowerMAX™ shielded solution comprises Category 6 component compliant patch panels, keystones and patch cords. When combined with DINTEK’s Category 6 FTP S/FTP cable, an end-to-end channel exists that maximises data throughput and provides headroom for all future technologies operating beyond one Gigabit. Combined with other DINTEK PowerMAX™ shielded products, our Category 6 cable is the perfect solution to your voice and data communications needs.


  • Voice
  • Fast Ethernet(IEEE802.3)
  • 100Vg-AnyLAN(IEEE 802.12)
  • Token Ring(IEEE 802.5)
  • TP-PMD(ANSI X3T9.5)
  • 100Base-T Ethernet(IEEE 802.3u)
  • 155/622 Mbps 1.2/ 2.4 Gbps ATM
  • 1000Base-T Ethernet
  • 550 MHz Broadband video


  • High performance, exceeds ANSI/TIA-568-2.D Category 6 Hardware
  • transmission performance
  • 100% shielded for complete EMI/RFI protection
  • Accepts 22-26AWG, Stranded or solid wire
  • Wiring: T568A/B


  • UL Listed
  • ISO/IEC 11801 2nd edition
  • ANSI/TIA Standard 568-2.D
  • CENELEC EN 50173

Ordering Information
Product NumberProduct NameOrientation


Std Pkg Qty


PowerMAX Cat.6 Shielded Toolless Jack




Technical Specifications
Connector HousingHigh Impact Flame-Retardant Plastic
StandardUL94v-0 rated
Front Connection
Contact TypeSpring Wire
MaterialPhosphor Bronze Alloy Plated with 50 micro-inch of Gold over 70~100 micro-inch of Nickel
Rear Terminals
Terminal TypeIDC
MaterialPhosphor Bronze Alloy with 10 micro-inch 100% Sn Alloy
Physical Ranges
Temperature Range
Stroage-40 to +70℃
Operational-10 to +60℃
Relative humidity
OperationalMax. non-condensing 93%
Retention50N (11 Ibf) for 60s ± 5s
Insertion/Extraction life750 cycles minimum
Number of IDC terminations200 minimum

Total mating force

800 grams for a 8 wire leads minimum

Insulation Resistance500 mΩ min.@ 100V d.c
Dielectric Withstanding Voltage1000 V d.c. or a.c. Peak Contact to Contact @ 60 Hz for 1 MIN.
Spring Wire Contact Resistance20 mΩ Max.
Voltage/Current Rating150VAC/1.5A
IDC Contact Resistance2.5 mΩ Max.

Strip 40mm of sheath from cable using stripper 

Roll back the braid or drain wire onto cable so it is out of the way.

Separate the four pairs and remove the foil wrap from around each pair.

Insert the wires through the back of the wire forming cap

Lay the wires into thier correct configuration, either T568A or T568B

Using side cutters, cut the wires level with the wire forming cap

Inset the wire forming cap into the rear of the jack body housing 

Roll back the braid or drain wire so it will fit under the jack body. Close the rear covers, pressing firmly until the jaws close and click into place

The finished connector should not show any wires at the back, the jacket should reach to the rear of the connector and the braid or drain wire should be tidy underneath the shield body.

Stay Up To Date

Thanks for coming to use the services provided by logging in to the DINTEK website. Press the login button.

Once you are logged into the DINTEK Website. You will have access to additional content and services depending on the level of access that has been assigned to you.